How To Remove Mold From Drywall - Painted and Unpainted (2023)

How To Remove Mold From Drywall - Painted and Unpainted (1)

Did you know mold on drywall can lead to serious respiratory disorders? It is important to remove mold as soon as you notice it has started to grow.

Methods for killing mold differ depending on if the walls are painted or not. In case the drywall is coated, it can be easy to clean by merely using water and an appropriate cleaning agent. However, the task is a lot more difficult when the wall is not painted.

There may even some occasions even where you need to simply remove the drywall and start again. But before we get you into a panic, let’s take a look at how to remove the mold using good old elbow grease.

Our recommended way of removing mold ondrywall is to use a mold fogger, however if you want to try other methods first then keep reading.

Disclosure:As an Amazon Associate I earn from qualifying purchases.However, this does not impact our reviews and comparisons. All opinions are our own we pride ourselves on keeping our articles fair and balanced. For more info see ourdisclosure statement.

How To Remove Mold From Drywall - Painted and Unpainted (2)

How to Remove Mold From Painted Drywall

Step 1: Select a mold killingcleaning agent

The market has a number of options when it comes to cleaning agents.

Ranging from mild to potent, the options are available in both chemical and natural alternatives. Depending on the severity of black mold problems, you may go for a stronger chemical if needed. The main options are:

  • Baking Soda:Create a cleaning solution with one part of baking soda added to five parts of water. It will be the mildest yet safest cleanser to use.
  • Vinegar: Mixing vinegar with equal parts of water can be a slightly stronger cleaning solution. It is completely natural and safe when you have pets or children around.
  • Detergents: Use detergents as per the directions on the bottle.These are completely safe to use with children or pets around.
  • Bleach: Not everyone recommends using bleach as its fumes canbe harmful to breathe in. However, it can be a strong effective cleaner that is safe for removing mold on drywall. Mixing one part of bleach with three parts of water can offer you a strong solution.
  • Concrobium Mold Control: This is by far our most preferred way to clean mold. It not only kills the mold, but creates a protective barrier so no mold can grow back. Can be bought in a handy spray bottle and no mixing is required.

Best Choice

How To Remove Mold From Drywall - Painted and Unpainted (3)

Our Preferred Mold Control

Concrobium Mold Control Spray

  • Use to eliminate mold, mildew, musty odors and prevent regrowth
  • EPA-registered formula crushes mold spores as it dries and leaves an invisible, barrier
  • Odorless solution cleans between 80-110 sq. ft. per 32 oz. bottle
  • Unique mold spray contains no bleach or harsh chemicals, safe for use on a wide range of surfaces

Step 2: Pour the cleaning solution into a spray bottle

Takeyour mixed cleaning solution and pour it into a spray bottle. Ensure that the solution is mixed thoroughly by shaking the bottle.

Step 3: Properly ventilate room

In the case that you are using a stronger chemical (bleach or mold control) you will want to make the room is well ventilated. Bleach especiallycontains harmful elements and should not be inhaled. So before you begin the cleaning process, make sure all the doors and windows are open.

During this step, you may also want to use an air purifier with a HEPA filter to stop the mold spores from spreading to another area.

Step 4:Protect surrounding areas

How To Remove Mold From Drywall - Painted and Unpainted (4)

Accidental spills of the chemicals or cleaners in use is possibleand might end up damaging items. Hence, move furniture and other belongings outside the room you are cleaning. Make sure you cover the floor using aplastic drop cloth.

Step 5: Spray the cleaning solution on the mold

Now you are ready to attack themold, take out the spray and spray a little bit on the mold.

Make sure you shake it well before using. You do not want todrench the area as additional moisture could result in an increase to the mold problem or damage to your walls.

The best thing to do here would be spraying the solution on the mold twice and covering it entirely with the solution, but makingsurethe solution is not running down the wall.

Step 6: Use a Brush

Use a soft bristle cleaning brush or an oldtoothbrush to scrub the area. If you do not haveeither of these, you may use the abrasive side of a dish sponge, just be careful not to damage your wall. You should scrub till you no longer see any visible mold around the area.

Step 7: Dry the Area

Areas left wet or damp are a breeding ground for mold, so dry the areas thoroughly by pointing an electric fan at the wall.

Step 8: Stain-blocking paint

Sometimes when you clean away mold ondrywall it will leave a stain that is impossible to remove by scrubbing. To cover this up you will need to use astain blocking primer and paint color of your choice to hide the stain.

How To Remove Mold From Drywall - Painted and Unpainted (5)

Stain-Blocking Paint

KILZ Restoration Maximum Stain and Odor Blocking Interior Latex Primer/Sealer

  • KILZ MAX is a water-base primer, sealer, stain and odor blocker developed with new technology that’s formulated to perform like oil-and shellac-based products.
  • KILZ MAX tackles tough stains from water damage, rust, smoke, nicotine, grease, tannin, ink, pencil, felt marker, pet stains and more while also sealing pet and smoke odors.

How to Remove Mold onDrywall – Unpainted

Removing black mold from unpainted drywall is much tougher due to the fact that the mold can penetrate much deeper due to their being no protective barrier, but all is not lost and it definitely possible if you follow the steps discussed below:

Step 1:Protect surrounding areas

Thefirstand foremost thing to do is to coverthe flooring and other surrounding areas by using a plastic drop cloth.Make sure you tape the sheet into place to ensure your surfaces are properly protected.

Step 2: Mark the mold

Follow this up by marking the mold on the walls by using a pencil. Mark a square/rectangle aroundthe mold making sure to leave some space between the visible mold and the pencil marks.This marked area also needsextend over two wooden wall beams that are behind the drywall. You will have to remove more wall than needed as this will ensure that you are removing the mold spores that are not visible to the naked eye. It will also enable you to replace that particular section of the drywall.

Step 3: Use a knife to cut the area

Use a jab saw for cutting the area by sawing piercing through the wall and sawing around the lines marked using the pencil.

It is important that before using the jab saw, you make sure there are no electrical wires, water pipes or other items that you may damage in the wall.

If you are unsure, make a very small hold with a screw driver first and slowly knock enough out of the drywall till you can make sure it is safe. After the marked area of the drywall becomes free, carefully remove the moldy piece and set it down on the plastic below.

Step 4: Clean the room with a HEPA vacuum

How To Remove Mold From Drywall - Painted and Unpainted (6)

Use a High-Efficiency Particulate Air (HEPA) vacuumto clean the entire room.

This needs to be done as mold spores may have beendisturbed and moved about during the cleaning process. If you can’t get a hold of a HEPA vacuum then a regular one will do.

Step 5: Carefully evaluate Doors & Windows

In the case that the mold was near any doors or windows, ask someone to spray water on the door or window from the outside using a hose.

Check if any moisture makes its way into the room. If you do notice that moisture is evident, then seal the leak from both the sides to prevent the leak from appearing again.

Step 6: Fit the new drywall

Cut a new piece of drywall to fit the hole you cut to remove the moldy area.Ensure it is as tight a fit as possible.

Step 7: Secure the drywall

Using drywall screwsattach the drywall to the wooden beams on the wall behind it.

Step 8: Apply Joint Compound

How To Remove Mold From Drywall - Painted and Unpainted (7)

The purpose of joint compound (also known as drywall compound) is to cover up the gaps between the new and old drywall and create a seamless finish. Apply thejoint compound over the perimeter of the new section of drywall. For a detailed guide on this, see this guide.

Step 9: Let the joint compound dry

Let the drywall compounddry for at least 24 hours. Follow this by using sandpaper to smooth the compound so it is flush with the wall after the compound has completely dried.
Step 11: Use a HEPA Vacuum cleaner

Lastly, clean the area with a High-Efficiency Particulate Air (HEPA) vacuum to remove any mold spores that might have landed inthe surrounding areas. The idea here is to clean everything thoroughly and remove any chance of the mold reappearing.

Using a Mold Fogger

There are some occasions when there is just too much mold to remove by hand. When this happens you can either rip all the drywall out and start again or you can try using a mold fogger.

Foggers produce a fine mist of Concrobium mold control that evenly covers all surfaces in the room. It not only kills mold, but also creates a protective barrier to prevent mold from re-growing.

We have a great guide here on how to use a mold fogger.

Best Choice

How To Remove Mold From Drywall - Painted and Unpainted (8)

Our Favorite Mold Control Fogger

Concrobium Fogger

  • Made in the USA
  • Light and even dispersal of formula
  • 400 sq ft of coverage
  • Contains no ammonia, bleach, orvolatile organic compounds
  • Actually kills the mold – eliminating it for good

Learn More

  • How to clean bath toys
  • How to get rid of mold on dry wall
  • How to remove mold from shower
Top Articles
Latest Posts
Article information

Author: Tish Haag

Last Updated: 08/26/2022

Views: 6160

Rating: 4.7 / 5 (47 voted)

Reviews: 86% of readers found this page helpful

Author information

Name: Tish Haag

Birthday: 1999-11-18

Address: 30256 Tara Expressway, Kutchburgh, VT 92892-0078

Phone: +4215847628708

Job: Internal Consulting Engineer

Hobby: Roller skating, Roller skating, Kayaking, Flying, Graffiti, Ghost hunting, scrapbook

Introduction: My name is Tish Haag, I am a excited, delightful, curious, beautiful, agreeable, enchanting, fancy person who loves writing and wants to share my knowledge and understanding with you.